Skip to main content
Roviral

MIT Magnetic Beads Track Muscle Motion for Prosthetic Limb Control

MIT researchers tested 3 mm implanted magnets that measure muscle length and speed, creating control signals for future robotic ankle-foot prostheses.

MIT Magnetic Beads Track Muscle Motion for Prosthetic Limb Control

Measuring what a residual muscle is doing could give a prosthesis a more direct control input. MIT researchers have tested magnetomicrometry, a method that tracks muscle motion using small implanted magnets and an external sensor. In three participants with below-knee amputations, the system recorded movement signals that could be translated into cursor control. The work points toward a possible input method for robotic ankle-foot prostheses, though the participants did not test it with a prosthetic limb.

Nidhi Agarwal
Magnetic beads implanted in muscle can reveal muscle dynamics for prosthetic control
Two implanted beads provide measurements of muscle dynamics. Christopher Shallal of MIT described the interface as minimally invasive and said it can provide information about how a muscle moves.

Reading movement from paired magnets

Magnetomicrometry uses pairs of magnets placed inside a muscle. As the muscle contracts or lengthens, the spacing between the magnets changes. A sensor worn on the skin detects that change, allowing the system to calculate muscle length and velocity. Those measurements offer a way to capture muscle dynamics directly, instead of relying only on movement elsewhere in the body as a proxy for the intended action.

The implanted beads are 3 millimetres in diameter, roughly the size of a sesame seed. Each contains an alloy of neodymium, iron and boron, coated with gold and parylene C, a polymer used here to make the bead biocompatible. A customised sensor sits over the muscles being measured and can read the magnetic signals from as far as 6 centimetres below the skin.

The arrangement divides the sensing task between a small implant and a wearable external component. The beads move with the muscle, while the surface sensor measures their changing separation without needing to be implanted. That combination is the core engineering idea: track internal tissue motion magnetically, then turn the measured motion into a signal a controller can use.

Testing control signals without a prosthesis

In the study, magnets were placed in up to four muscles associated with the ankle joint. The procedures took place at Brigham and Women’s Hospital in collaboration with plastic surgeon Matthew Carty, a co-author of the research. Three participants with below-knee amputations took part in the measurements.

Nidhi Agarwal

The experiments did not involve wearing a prosthetic limb. Instead, participants used muscle movements to move a cursor on a screen toward a target. Signals from each of three measurement techniques were converted into cursor commands. The researchers’ proposed next application is to feed such signals to the controller of a robotic ankle-foot prosthesis.

That distinction matters when judging how far the demonstration goes. Cursor movement shows that muscle measurements can be mapped to a control task; it does not establish how the interface will perform during walking, how it will respond to changing loads, or how reliably it will work over long periods. Those questions require testing with the intended prosthesis and in the conditions where a user would rely on it.

Why the measurement could matter

Prosthetic control depends on converting a user’s intent into commands that a device can interpret. Muscle length and velocity provide two kinds of information about motion: how far the muscle has changed length, and how quickly that change is happening. A controller receiving those measurements could, in principle, use them to infer movement intent and adjust the prosthesis accordingly. The study demonstrates a route for producing those inputs, rather than a finished control system.

MIT graduate student Christopher Shallal, one of the paper’s lead authors, described the interface as minimally invasive and said that placing two beads in a muscle provides access to information about muscle dynamics. The implant size and the sensor’s ability to read signals through several centimetres of tissue are relevant to whether this approach can be made practical. The available results, however, cover three participants and a cursor task; they don’t establish broader clinical performance or accessibility.

For prosthesis designers, the next engineering step is to connect this sensing method to the device controller and evaluate the resulting user control. That will show how measurements of muscle motion translate into useful movement of an ankle-foot prosthesis. For now, the key result is a demonstrated sensing path from implanted magnetic beads, through an external skin-mounted sensor, to control signals.

Source: Nidhi Agarwal · www.electronicsforu.com

Filed alongside