ScioSense UFM-G01 Uses Ultrasonic Sensing for Residential Gas Metering
The UFM-G01 measures G4-class gas flow with ultrasonic pulses, combining flow, pressure and temperature sensing in a battery-oriented module.

For residential gas meters, the ScioSense UFM-G01 replaces moving mechanical parts and thermal flow sensing with ultrasonic measurement. Its design targets G4-class meters, where low pressure loss and modest energy demand matter alongside measurement accuracy. The module is also intended for small commercial gas systems, burners, boilers and low-flow leak detection.

Flow measurement from pulse timing
Two ultrasonic transducers sit inside the gas pipe and send pulses through the flow. The difference in pulse travel time provides the basis for calculating volumetric flow. This approach avoids placing a mechanical meter element in the stream, which ScioSense says helps keep pressure loss below 150 Pa. The low loss may be useful in systems where the meter has to measure flow without imposing a substantial restriction.

The UFM-G01 supports flow rates from 16 to 7200 litres per hour and reports accuracy of up to ±1.5%. Those figures define a wide operating span for residential metering, though the published information does not specify the conditions used to determine accuracy across that range. Engineers evaluating it for a particular meter will need to check performance against their gas composition, flow profile and installation requirements.

Ultrasonic timing also gives the module access to speed of sound in the gas. That measurement is included alongside transient and cumulative flow, gas temperature and pressure. ScioSense lists support for air and methane (CH4), so designs using other gas mixtures should confirm compatibility with the supplier before treating the module as a drop-in measurement element.

Integrated measurements and power envelope
The module incorporates pressure and temperature sensors rather than leaving those measurements entirely to the host system. Its pressure range is 260 to 1260 hPa, and its specified operating temperature range is -20°C to +50°C. Combining these signals with flow and sound-speed measurements gives the host device several readings relevant to monitoring the gas and the meter's operating state.

Battery operation is a stated design aim. The UFM-G01 accepts a supply from 3.2 V to 5.5 V and has typical energy consumption of 262 mAh per year. Its pulse frequency can be changed in software to reduce consumption further. That makes the pulse setting a system-level design choice: lowering activity may help conserve energy, while the resulting measurement behavior should be checked against the application's response and accuracy needs. ScioSense does not specify the conditions behind the annual consumption figure.

Software adjustment may also help meter designers tune operation for their own reporting cadence and power budget. The available product details do not give a communications data rate, a measurement update interval or the host-side protocol framing, so those integration details will need confirmation during design-in.

Packaging and intended service life
ScioSense describes the UFM-G01 as a plug-and-play module with UART communication to a host device. That interface provides a direct route for sending measurement data into a meter controller, while the integrated sensing reduces the number of separate measurement components the surrounding design needs to accommodate. ScioSense also says it can customise the module for specific customer requirements.
The company designed the sensor to minimise contact between the sensing technology and the gas stream and states a service life of up to 15 years. That is a target relevant to installed meters, where replacement and maintenance access can be costly. The published details do not provide qualification procedures or operating conditions for the service-life figure, so it should be treated as a manufacturer specification to validate for the intended application.
The combination of ultrasonic flow measurement, integrated pressure and temperature sensing, and UART output gives meter developers a compact alternative to conventional thermal or mechanical approaches. Its practical fit will depend on verifying the stated accuracy over the required flow range, confirming gas compatibility, and matching the adjustable pulse rate to the meter's energy budget. ScioSense presents the UFM-G01 for G4 residential meters as well as several low-flow gas applications, with the pressure-loss and battery figures central to its intended use.
AXT and Stärke-AMG Plan Adelaide SAF 3D Printing Capacity
Fluke ii1050 and ii1030 Acoustic Imagers Add 202 Microphones for Industrial Inspections
KIMM LED System Changes Object Colours While Keeping Room Lighting White